The DV XX-1 was the first cartridge to feature a "magnetic flux damper" (patent) and softened magnetism" (patent) processes that reject the magnetic fluctuation that is detrimental to a moving coil cartridges performance.
The DV XX2MKII is the outstanding result of Dynavectors' continuing research and advanced technology.
Low output MC with Flux damper and Alnico magnet XX2 MC cartridge
The DV XX-1 was the first cartridge to feature a "magnetic flux damper" (patent) and softened magnetism" (patent) processes that reject the magnetic fluctuation that is detrimental to a moving coil cartridges performance.
The The DV XX-2 MKII retains the benefit of the flux damper but features the Alinco-5 magnet and the similar rigid construction to the Te Kaitora Rua. Alnico magnets exhibit high magnetic flux density combining with a low coercive therefore magnetic resistance is lower than other magnetic types such as rare earth and ferrite, providing the exceptional stability of the XX-2 MKII output voltage. There is also the additional advantage of low magnetic and electrical resistance contributing to a discernable improvement in sound quality.
The XX-2MKII also exhibits deep powerful bass, treble is both clear and lively possessing none of the hardness found in many moving coil designs.
The XX-2MKII also features a 6 mm solid boron cantilever fitted with a Pathfinder Line contact stylus. PCOCC (pure copper ohno continuous casting process) copper wire is used for the coil. The output voltage of 0.28mV is higher than that of the XX-2 and 6 ohms impedance are suited to most moving coil phono stages.
For ridgity of construction the XX-2 MKII cartridge body is machined from 7075 aluminium the hardest available. However, having only a total weight of only 8.9 grams it is suitable for a variety of popular tonearms.
Type - Low output moving coil cartridge with Alnico magnet and Flux damper
Output Voltage - 0.28mV (at 1KHz, 5cm/sec.)
Channel Separation - 30 dB (at 1KHz)
Channe
9" precision tonearm with carbon-fibre armtube / headshell, as found on Pro-Ject premium turntables.
Pro-Ject's 9" precision tone arm with carbon-fibre armtube is efficiently designed to lead parasitic vibrations away from the cartridge into the mounting board which guarantees the precise tracking of the record grooves by the needle and also facilitates fine adjustment of vertical and horizontal tracing
Key Features
The headshell and armtube are fashioned from a single piece of carbon-fibre
Conical armtube avoids standing wave reflections
Inverted bearing design with four ABEC7 spec ballraces
Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonance
Sorbothane damped counterweight effectively counteracts unwanted resonances
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracking angle)
Single Screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell
Straight armtube reduces toe-in error
Silicone damped armlift can be adjusted to suit arm height
The internal wiring consists of flexible high purity copper from the headshell right through to the gold plated phono sockets
Available with 5-pole standard socket, flying lead or terminal with phono sockets and earth screws
* All Pro-Ject arms are available with 'flying lead' or 5-PIN DIN terminations. Most models are special order only. Call for info.
Headshell:
0.5" (12.7mm) Standard
Mounting Distance:
212mm
Supplied Counterweight:
For Cartridges Weighing Between...5-7g, 5g, 7-10g, 9-11g and 10-14g
Downforce Range:
10 - 35mN
Effective Length:
9" (230mm)
Effective Mass:
8g
Overhang:
18mm
Weight:
265g (Without Counterweight)
Please Note: This item is just the tonearm, not a turntable.
Fitting to non-Pro-Ject turntables:
If you wish to use the tonearm on a Linn turntab